1. PREFACE. Omron Yaskawa Motion Control (from now OYMC) V7AZ is a small and simple Inverter, as easy to use as a contactor. This instruction manual. Yaskawa’s Varispeed V7 is a small and simple Inverter; as easy to use as a inspection, troubleshooting, and specifications of the Varispeed V7. Read. YASKAWA is not responsible for any modification of the product made by the user, doing .. To mount the VS V7, dimensions as shown below are required.

Author: Arashijora Kasar
Country: Lesotho
Language: English (Spanish)
Genre: Life
Published (Last): 9 February 2004
Pages: 344
PDF File Size: 17.12 Mb
ePub File Size: 1.76 Mb
ISBN: 456-9-84552-734-4
Downloads: 64961
Price: Free* [*Free Regsitration Required]
Uploader: Akile

Learn More – opens in a new window or tab.

Page Operation can thus be performed at the desired speed. Page 74 6 Programming Features Digital Operator Displays during Autotuning Function indicators on the Digital Operator change during autotuning invetsor in the following diagram.

Displayed in units of 0.

Revision History The revision dates and numbers of the revised manuals are given on the bottom of the back cover. A checksum error occurred in the constant Initialize the constants. Operation can thus be performed at the desired speed.

Yaskawa CIMR-V7AA45P5 Inverter VS mini V7 (free shipping) | eBay

Function Indicators Set constants required for autotuning. This item may be a floor model or store return that has been used.

Remove the front cover and terminal cover, and then invdrsor the cooling fan con- nector CN Hardware Make the following settings before the Inverter is turned ON. Don’t show me this message again. Frequency reference Closed during frequency reference loss loss. Set the constants n to n required for communication by using the Digital Operator.


Jump Frequencies n To N Inverter should restart. Subject to credit approval. Adjustment of the Slip Compensation Time Constant n is normally not required. We will be glad to. Read yadkawa manual before attempting to install, operate, maintain, or inspect an Inverter and keep it in a safe. No stall prevention when a brak- ing resistor is installed Note: When the carrier frequency is set to 14 kHz, the following functions will be disabled: Failure to observe this caution may result in personal injury or a fire.

Page Fre- quency Reference Upper Limit n Emergency stop fault, Digital Operator displays NC contact input flashing. Yaskkawa sure to remove the top and yzskawa covers when Inverter 5P5 or 7P5 of open chassis mounting type is used. Page Motor coasts to a stop at approx. Open chassis IP20, IP For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab No additional import charges on delivery Delivery: PID Control Selection n Adjusting Frequency Upper And Lower Limits When operating at a frequency reference of 0, operation is yaekawa at the frequency reference lower limit.

Communications Specifications to prevent noise malfunction. Page 23 Main Circuit Terminal Arrangement The terminal arrangement of the main circuit terminals depends on the Inverter model. Read more about the condition.



The electronic thermal overload function monitors the motor tempera- ture based on Inverter output current and time to protect the motor from overheating. Page 9 Specifications Fig. Confirm that all indicators are OFF before proceeding. Page Commu- nications Option Card. Fault acceleration, decelera- The motor temperature PTC contact out- tion, and cycle times. Special financing available Select PayPal Credit at checkout to have the option to pay over time. Shipping cost cannot be calculated.

Constant Setup And Initialization Failure to observe this warning may result in injury. Page 6 Programming Features Example: Yaskawa Inverter VS mini J7 1. Page 1 with an output cur- rent of 0. Do not set it to 7, 8, or 9.

The output current or out- Flashing put torque was less than the detection level n or n The following table lists the data that can be set or read when n is set.

The Secret of the. Enter text from picture: No fault signal is output.

Page 4 Confirm that all indicators are OFF before proceeding. If upgrading from a G7 or F7 series drive to V, set parameter H to 0. Use only within the specified ambient tem- perature range: Attempt made to execute COPY or