# LM355 DATASHEET PDF

The LM series are precision easily-calibrated integrat- ed circuit temperature sensors Operating as a 2-terminal zener the LM has a breakdown voltage. lm are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for lm Data sheet, LM manual, LM pdf, LM, datenblatt, Electronics LM, alldatasheet, free, datasheet, Datasheets, data sheet, datas sheets, databook. Author: Faucage Tezahn Country: India Language: English (Spanish) Genre: Education Published (Last): 16 May 2011 Pages: 210 PDF File Size: 20.24 Mb ePub File Size: 7.76 Mb ISBN: 855-8-75959-686-3 Downloads: 52939 Price: Free* [*Free Regsitration Required] Uploader: Maujind This lm3555 so that we can hook our arduino to a computer and send it code that it can run to display to us the temperature. The type B side of the connector goes into the arduino and the datasheeh A side into the USB port of the computer. In this project, we will demonstrate how to build temperature sensor circuit using a LM sensor. Temperature Sensor Circuit The temperature sensor circuit we will build is shown below: Once this analog voltage in millivolts is calculated, we then can find the temperature in kelvin by the equation: It is divided by because a span of occupies 5V.

So to get the degree value in fahrenheit, all that must be done is to take the datasheeet output and divide it by this give out the value degrees in fahrenheit. Pin 2 is the output pin.

So you circuit connections are: This will be the raw value divided by times Dahasheet if the LM is giving an output reading of 2. The output pin provides an analog voltage output that is linearly proportional to the fahrenheit temperature.

DIN 50939 PDF

## View lm355 datasheet:

Once we obtain this Celsius value, we can convert into Fahrenheit with the following equation: This is because there is millvolts in 5 volts. Since the output pin can give out a maximum of 5 voltsrepresents datadheet full possible range it can give out.

This translates into the circuit schematic: We can now write code in the processing software to give instructions to the arduino.

We can use any type of arduino board. This output reading of We can then easily convert this value into fahrehnheit and celsius by plugging in the appropriate conversion equations. The arduino, with suitable code, can then interpret lm3555 measured analog voltage and output to us the temperature in degrees Kelvin, Celsius, and Fahrenheit.

## How to Build a LM335 Temperature Sensor Circuit

All you have to do is take the output reading and divide it by 10 in order to get the temperature output reading. We attach this pin to analog pin A0 of the arduino board. Pin 2 gives an output of 1 millivolt per 0. Once we have this ratio, we then multiply it by to give the millivolt value. All we must do is write this code and upload it to the arduino to convert this kelvin temperature into fahrenheit and celsius.

The difference between an LM and LM34 and LM35 temperature sensors is the LM sensor gives out the temperature in degrees Kelvin, while the LM35 sensor gives out the temperature in degrees Celsius and the LM34 sensor gives out the temperature in degrees Fahrenheit.

ANTIGUOS MITOS JAPONESES NELLY NAUMANN PDF

### National Semiconductor – datasheet pdf

We will integrate this with the arduino to measure the temperature. As a temperature sensor, the circuit will read the temperature of the surrounding environment and relay this temperature to us back in degrees Kelvin. Dataxheet can adjust this value to meet your personal preference or program needs. This is ideal because the arduino’s power pin gives out 5V of power. This allows us to calibrate the temperature sensor if we want a more precise temperature readout. The IC has just 3 pins, 2 for the power supply and one for the analog output. Now the computer is connected to the arduino. Pin 1 is the Adjustable Pin Adj.

The raw voltage over this value therefore represents the ratio of how much power the output pin is outputting against this full range. Pin 3 is the ground pin and connects to the ground GND terminal of the arduino. So, for example, if the output pin, pin 2, gives out a value of mV 0.

We get the ratio of the raw value to the full span lm35 and then multiply it by to get the millivolt value.